Radio shack is selling a contact cleaning pen that is made by Caig Labs for gold contacts - not cheap but great! Destroying Data If you are replacing a failing hard drive or simply discarding a drive that is no longer large enough, you may worry about someone recovering your data from it. Fdisk reports wrong size when using drives larger then 64GB According to Microsoft KB article Q263044, "When you use Fdisk.exe to partition a hard disk that is larger than 64 GB On many motherboards you must go into the BIOS and actually either enable or disable the secondary drive controller and save the changes. weblink
For an SATA drive, any circuit board failure makes it difficult to access the drive, because every SATA drive acts as its own disk controller. I first tried swapping the drives around without unplugging the motherboard end of the ide cable, so would not have reversed them. After rebooting the drive will be automatically detected. Most likely on drives that are more than 528MB, the LBA setting is not enabled. http://www.computerhope.com/issues/ch000446.htm
A quick note from the author. Edited by hamluis, 05 September 2012 - 06:29 AM. Although it doesn't completely eliminate the power supply as the cause a power supply can be failing rather than simply being marginal for the load you can try reducing the load
plugged the cdrom into the ide port that normally connected to the hard disk) and that worked fine, so the ports and cables all look okay. With Vista, no UPS lasts long enough to allow you to save your files and shut down a system cleanly. 0 JonnyDough Jun 11, 2008, 12:20 PM Quote: Speaking just for It is reasonably priced and WILL repair hard drive problems WITHOUT destroying your data. Hard Drive Controller Board Replacement All hard drives have at least two cables connected to the back of the drive.
Note: if the cables appear to be connected properly, consider disconnecting and then reconnecting the cables to ensure they are firmly connected. Hdd Controller Failure Symptoms Jan 17, 2006 #6 dmill89 TS Guru Posts: 475 Don't forget to partition and format the HDD. These settings must match the required settings of the manufacturer. https://www.ifixit.com/Wiki/Hard_Drive_Troubleshooting Not much can be done in this condition other then replace the drive. 5.
Thank you so much, I am really frilled by your outstanding services. Hard Drive Problems And Solutions Obviously, if you are using a circuit board from an existing drive, be sure to back up the contents of that drive before you proceed.If the drive is not accessible and Superb! This should bring up a black and white screen which at the top has three choices - 'Safe Mode'; 'Safe Mode with networking'; and 'Safe Mode with Command Line', and in
BTW, 486sx isn't much different than 386DX - not worth putting a lot of time or money into. http://www.bleepingcomputer.com/forums/t/467539/critical-error-hard-drive-controller-failure/ It isn't. Hard Drive Controller Failure Although it's uncommon for a motherboard interface to fail spontaneously, it does happen rarely. Hard Disk Troubleshooting Steps He did take apart the case.
Another way is to use a utility program like Norton Utilities to perform the surface scan. http://fileupster.com/hard-drive/hard-drive-imminent-failure-fix.html Attempts by IT guy - not successful; says hardware problem. Social Sharing Find TechSpot on... Step 1: Diagnose your driveShow All Items You need to determine if your drive is not functioning due to mechanical or electrical failure. Hard Drive Troubleshooting Flowchart
Bad hard drive If you continue to experience the same issues, the hard drive may be bad. The board I procured from Hard Drive Parts came with simple instructions and even a torx driver. or less (or check the various For Sale/Trade sections here and at Anandtedh) - an added benefit will be the support of larger/faster drives. check over here I also touched each of the integrated circuits (ICs) on the controller and found that one of the them was very hot (refer to picture).
If it is electrical failure then replacing the controller may or may not fix the problem, if it is mechanical failure replacing the controller will most certainly not fix the problem. External Hard Disk Troubleshooting I closed out of all those popups, but as soon as I did all of the icons on my desktop disappeared. The hard drive has failed electronically This will be indicated by an error message during the computer boot cycle.
Choose 'Safe Mode with networking' - you may need to use the 'Up and Down arrow keys to select it, then press 'Enter'. Jan 6, 2006 #1 Samstoned TechSpot Paladin Posts: 1,018 can you hold the drive in your hand while the system is on if so does it feel like its spinning if If it is electrical failure then replacing the controller may or may ... 2 Step 2: Find the serial / part numbers on the driveFor my model of Maxtor hard drive Hard Disk Troubleshooting Pdf All Rights Reserved.
Other Information Formatting a hard drive You are at the www.techadvice.com site which is not associated with the company or products shown on this page. In Windows 95 you can use the scandisk which is found in the Start/Programs/Accessories/System Tools folder. You do this by starting up your computer, and when the BIOS screen appears, start tapping the F8 key. this content The system generates an exception error when using a reference to an invalid system memory address.