You can always backup your current BIOS before writing a new one. Tango Icons © Tango Desktop Project. Visit our corporate site. Another reported mistake is to have the BIOS ignore the disk on which the kernel or GRUB stages reside. this contact form
Error 18 I've booted from the CD and given the output to these commands: free -m: Mem: total 181, used 178, free 2, shared 0, buffers 4, cached 57 -/+ buffers/cache: Join Date Oct 2009 Location Poland Beans 51 DistroUbuntu 10.04 Lucid Lynx Re: grub loading stage 1.5, error 18 This may be helpful: http://members.iinet.net.au/~herman546/p15.html#18 Adv Reply Quick Navigation Networking & Please jesus don't use the ntloader, there are a few other fairly good boot loaders out there but they all fail in comparison to GRUB and Lilo. Check if you have any BIOS update for the controller from the vendor site.
Two Ultra Wide SCSI HDD's. 36GB each. Latest LQ Deal: Complete CCNA, CCNP & Red Hat Certification Training Bundle Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs Home Forums HCL Reviews Tutorials Articles Register Search i would avoid it unless you are either quite experienced with this type of thing or else don't care if the machine gets trashed. gentoo.org sites gentoo.org Wiki Bugs Forums Packages Planet Archives Sources Infra Status Wiki Toggle navigation Main pageRecent changesHelp Gentoo Gentoo Projects Documentation Gentoo HandbookGentoo FAQFeatured DocumentsTopicsCore systemHardwareSoftwareDesktopServer & SecurityProject & Community
A LiveCd only needs a cd/dvd-drive, it doesn't need a hard-drive. Missing GRUB image Situation When booting the system, the spiffy Gentoo splash screen is not seen. I will try and upgrade the ram over time. Like this:Like Loading...
LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware Grub Loading, Please Wait......Error 18 User Name Remember Me? Is there any way of getting around the GRUB bottleneck or must I write off the two hours or so I spent loading Debian??-- Frank Halliwell ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~Mail - [email protected] Homepage at see below: Grub Stage 1.5 Grub Loading, Please Wait Error 18 I've researched this GRUB error and I was able to find that the error basically means that the HDD's connected look at this site Option 1 has a few alternatives such as installing the full Ubuntu and then trying out those various DEs and WMs but you would probably have to do this from a
Are misspellings in a recruiter's message a red flag? If there is a way around this problem, would running a BIOS upgrade on the card cause any further problems? If this isn't possible then we could easily work-around what's there as it doesn't really seem to be as bad as it might look. Any help would be thankfully received.
All seemed to go well, I was not even prompted about Grub (unlike when W2k was still on the system). https://marionote.wordpress.com/2010/07/03/grub-error-18-debian-linux-5-05-lenny/ Xel'naga666 View Public Profile View LQ Blog View Review Entries View HCL Entries View LQ Wiki Contributions Visit Xel'naga666's homepage! There should be a grub advisory on the disk! OK, here is the scenario: You go into a elementar...
Next, chroot into the Gentoo system and do a listing of the available files to see what kernel images there are available: root #cd /boot root #ls This will list all http://fileupster.com/grub-loading/grub-loading-error-25-please-wait.html A better option is to check your motherboard manufacturer's website for an update to the BIOS, which could make this problem disappear. I reinstalled the whole Ubuntu again, nothing. Note that registered members see fewer ads, and ContentLink is completely disabled once you log in.
It saved me twice!! Sadly this'll mean you'll have to run the install again but it *should* work. Solution Mount the boot partition and verify if the grub/grub.conf file exists. navigate here The contents of this document, unless otherwise expressly stated, are licensed under the CC-BY-SA-3.0 license.
Solution - Booting an entry First, verify that the root and setup lines that were used are correct. Will it automatically go to the newly partitioned drives? Thanks boot multi-boot grub share|improve this question asked Oct 7 '09 at 19:11 Pierre 1136 add a comment| 1 Answer 1 active oldest votes up vote 1 down vote The wiki
Logged adrian15 Administrator Hero Member Posts: 833 Please test Rescatux and report back feedback... GRUB returned the terse message "Error 18". If so then deleting sda2 (the Extended Partition) and all the other linux partitions should be quite easy allowing us a fresh start. http://fileupster.com/grub-loading/grub-loading-error-18-debian.html Solution Strictly speaking, this is no GRUB error.
Solution According to The_Bell, changing the boot order in the BIOS can solve the problem. If attempting to boot the system using a GRUB floppy, the problem disappears. A 1997 mark controller should not be a problem. About Me Name: Billy Nair Location: Utah, United States Born in Kapiolani Children's Medical Center, just a few blocks from Waikiki.
Had the message and figured it was a bad install so installed Slackware 10.1 had the same error. Appease Your Google Overlords: Draw the "G" Logo How exactly does the typical shell "fork bomb" calls itself twice? I formatted a 60Gb drive at a low level (using the Maxtor Powermax utility) and then I let the Ubuntu installer do its thing. Be sure to check the root(x,y) settings in grub.conf.
The install went smooth and it ejected the CD and said hit Enter. Re: Error 18 Grub loading please wait « Reply #1 on: 2009/09/28, 16:51:04 pm » Quote from: chef11994 on 2009/09/26, 18:06:40 pmWow I knew super grub existed but I just created Did having a fat32 part. A completely different distro might be better for this machine.
Why does this execution plan have Compute Scalars? Are you new to LinuxQuestions.org? Solution cyrillic provides information that it is possible to "map" the disks in a different order by changing grub.conf's Windows entry like so: FILE grub.confMapping diskstitle Windows XP map (hd0) (hd1) Error 18 From: "Ryan Niebur"
Upgrade the Portage tree or mask this version of GRUB: root #echo "=sys-boot/grub-0.93.20031222" >> /etc/portage/package.mask root #emerge --ask sys-boot/grub:0 Another option is using the grub-install script as is recommended by the Most importantly ... cause this problem?? By joining our community you will have the ability to post topics, receive our newsletter, use the advanced search, subscribe to threads and access many other special features.
It was a while ago and I have since upgraded to Ubuntu 6.10. This may take a long time 8.1 Situation 8.2 Solution 9 When installing GRUB, it just hangs 9.1 Situation 9.2 Solution 10 Uncompressing Linux...